Will a LS7 intake fit on a LS1?
The MSD Atomic AirForce intake is available for LS1, LS2, LS3, LS6, LS7, L99, and LT1 applications. It’s compatible with both stock and aftermarket fuel rails. 2.
What size is a LS7 throttle body?
90mm
12605109 – LS3/LS7 90mm DBW Throttle Body.
How big is a stock LS1 throttle body?
Most aftermarket manufacturers produce throttle bodies in the 90-105mm range (some slightly larger) for use with stock and aftermarket LS intakes. Most factory intakes will not accept a throttle blade larger than a 90-92mm due to design with impregnated gasket and bore relation.
Are LS3 and LS7 intakes the same?
Because the ports on the LS7 head and LS3/L92 heads are shaped differently, intake manifolds must be matched up accordingly. For instance, the LS3 intake manifold isn’t compatible with LS7 heads, and the LS7 intake won’t work on LS3 heads.
Can you put LS7 heads on a LS1?
LS7 has 12 degree valve angle, the C5R head has an 11 degree valve angle. These can be considered a raised port position and will not accept previos intake manifolds. 8. Likewise the LS7 intake manifold therfore cannot be used on the LS1/LS2/LS6 & LQ heads.
How much HP can an LS7 make?
The LS7 is the largest displacement member of GM’s LS engine family, and it is an absolute beast right out of the box. Rated at 505 hp and 470 lb-ft of torque, this 7.0L unit was offered in the Chevrolet Corvette Z06 from 2006 to 2013, as well as the 2014 and 2015 editions of the Chevrolet Camaro Z28.
What size is the LS1?
The LS1 (5.7 liter, 346ci) was the engine that started it all. Given the Gen III designation and introduced in the 1997 Corvette and the Camaro/Firebird in 1998, it was a huge departure from the previous LT1 (Gen II) powerplant and included features such as a deep-skirt aluminum block and coil-near-plug ignition.
Can you put LS7 heads on an LS3?
You will be able to run LS7 style heads on LS3 engines very shortly.
Will LS6 headers fit an LS7?
LS6 and current FAST intake manifolds will NOT fit the LS7 or C5R heads due to the difference in intake port shape (Cathedral vs. rectangular) and port location/valve angle.
What is the best intake manifold for an LS1?
Billet Aluminum Intake Manifold for LS1, LS3, or LS7 By Shaun’s… Free Shipping! Edelbrock 90mm LS Series Throttle Body Without IAC or TPS… Edelbrock 90mm LS Series Throttle Body Without IAC or TPS… Edelbrock High Flow Intake Elbow for 120mm Throttle Body… Edelbrock High Flow Intake Elbow for 95mm Throttle Body to 4150…
What kind of throttle body does an LS1 have?
The very first LS throttle body was an electronic throttle, also known as drive-by-wire. The electronic throttle was released before the cable throttle, but in 1998, the LS1 engine for both Camaros and Firebirds moved to cable throttle.
How has the LS throttle body evolved over time?
As the LS evolved over time, so did their throttle bodies, becoming more efficient and much easier to tune. With the introduction of the original LS engine in 1997, throttle body configurations have ranged from cable driven to drive by wire (electronic), to three and four bolt, and even up to bigger throttle bodies such as the 102mm.
What kind of throttle body does a corvette have?
For these early LS engines, like those found in the C5 Corvette, the throttle body design features the three bolt configuration with a 78mm blade. The very first LS throttle body was an electronic throttle, also known as drive-by-wire.