How do I connect to APC PDU?
Use the supplied serial cable (APC part number 940-0144A) to connect the selected port to the serial port on the front panel of the Rack PDU. 3. Run a terminal program (such as HyperTerminal) and configure the selected port for 9600 bps, 8 data bits, no parity, 1 stop bit, and no flow control. Save the changes.
How do you connect PDU?
Connect an Original PDU to a Static IP Address Network
- Connect a crossover patch cable from the system to the PDU metering unit’s RJ-45 Ethernet port.
- Connect the PDU power input lead to the AC power source.
- On the system, use a web browser to log in to the PDU metering unit.
How do I find my PDU IP address?
For PDUs with a display screen: Press and hold the select button for a few seconds. Once “IP” appears on the display screen, release the button. Your unit will then display the IP address in a sequence of four groups.
What is the default IP address for APC PDU?
systems, the switched PDUs have the IP address of ‘10.20. 2. x/255.255. 0.0’….Old Firmware.
System IP | 10.20.2.1 |
---|---|
Subnet Mask | 255.255.0.0 |
Default Gateway | 10.20.255.254 |
How do I reset APC Switched Rack PDU?
Resetting APC AP7920 PDU
- Press and hold the reset button for about 10 seconds.
- The status light should blink rapidly.
- Release the reset button then press it again for about a second.
- The light should go orange.
- After about 20 seconds the reset will complete and the device will have booted.
What is the default password for APC PDU?
The default username and password for apc pdu is “apc”. It is a common username and password and can be used for setup and installation of APC Management Card setup, BOOTP and DHCP configuration, Local access to the control console among others. Please refer to the following page to know more about APC PDU setup.
How do I reset my APC Network Management Card?
Press and hold the NMC’s pinhole reset button for 20+ seconds, ensuring the NMC’s status LED is pulsing green during this time. When it changes to amber or orange, release the reset button to let the format function complete and for the NMC to complete its reboot process.
How do I restart PDU?
A: Most PDUs have a small unlabeled button located behind a hole next to the LED displays or network port. Utilizing an item such as a paper clip, you can depress the button. Press and hold the button for between 10 and 15 seconds. After releasing the button, the unit will initiate a factory reset.
What is the default IP address for APC Network Management Card?
The default IP address is 192.168. 2.66 with a subnet mask of 255.255. 255.0.
How do I set up my switched rack PDU?
Enter your user name and password. If the PDU uses a non-default port number (between 5000 and 32767), you need to include a colon or a space (depending on your telnet client) after the IP address and then the port number. You can use a local computer that connects to the Switched Rack PDU through the serial port on the front of the unit.
What is an APC PDU?
Features of the PDU The APC ® Switched Rack Power Distribution Unit (PDU) is a stand-alone, network-manageable device that allows programmable control of eight, sixteen, or twenty-four power outlets (depending on the model). You can control a PDU remotely through its Web, control console (serial or telnet), or SNMP interfaces.
How do I connect my PDU to a local computer?
If the PDU uses a non-default port number (between 5000 and 32767), you need to include a colon or a space (depending on your telnet client) after the IP address and then the port number. You can use a local computer that connects to the Switched Rack PDU through the serial port on the front of the unit. 1.
Does the switched rack PDU use a DHCP server?
Introduction Overview In addition to using a BOOTP server or manual settings, the Switched Rack PDU can use a dynamic host configuration protocol (DHCP) server to provide the settings that it needs to operate on a TCP/IP network.